Datenblatt-pdf.com


81006 Schematic ( PDF Datasheet ) - Maxim Integrated

Teilenummer 81006
Beschreibung High Level Analog Switches With Drivers/ Monolithic Silicon
Hersteller Maxim Integrated
Logo Maxim Integrated Logo 




Gesamt 15 Seiten
81006 Datasheet, Funktion
REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
F Add peak current to absolute maximum ratings. Editorial changes throughout.
G Changes in accordance with NOR 5962-R144-95.
H Make corrections to the switch operation table in 3.3.1. Update boilerplate to
reflect current requirements. -rrp
92-11-24
95-10-20
03-03-10
APPROVED
M. A. FRYE
M. A. FRYE
R. MONNIN
CURRENT CAGE CODE 67268
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
REV
HH
SHEET
12
PREPARED BY
Gary J. Zahn
CHECKED BY
William E. Sharp
APPROVED BY
N. A. Hauck
DRAWING APPROVAL DATE
81-10-01
HHHHHHHHHH
3 4 5 6 7 8 9 10 11 12
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216
http://www.dscc.dla.mil
MICROCIRCUIT, LINEAR, CMOS, HIGH LEVEL
ANALOG SWITCHES WITH DRIVERS,
MONOLITHIC SILICON
AMSC N/A
REVISION LEVEL
H
SIZE
A
CAGE CODE
14933
SHEET
DSCC FORM 2233
APR 97
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
1 OF
12
81006
5962-E243-03






81006 Datasheet, Funktion
TABLE I. Electrical performance characteristics – Continued.
Conditions
Test
Symbol
-55°C TA +125°C
VCC = ±15 V
Group A
subgroups
unless otherwise specified
Logic supply current
+IL VIN = 0 V, 5 V
Reference supply current
+IR
VIN = 0 V, 5 V
Turn-on time
tON
Turn-off time
tOFF
Single channel isolation 2/ VISO
Crosstalk between channels VCT
2/
Charge transfer error 2/ VCTE
Break before make time
delay
2/
tD
Driver input capacitance 2/
Switch input capacitance
2/
CA
CIS
Switch output capacitance COS
2/
RL = 100 , f = 100 kHz,
VIN = 2 VP-P, CL = 5 pF,
TA = +25°C
RL = 100 , f = 100 kHz,
VIN = 2 VP-P, CL = 5 pF,
TA = +25°C
VIN = 0 V, CL = 10 nF,
TA = +25°C
TA = +25°C
VIN = 0 V, TA = +25°C
Switch off, TA = +25°C
Switch off, TA = +25°C
1, 3
2
1
2, 3
1, 3
2
1
2, 3
11
9
10
11
9
10
11
9
10
11
9
10
9
9
9
9
9
9
9
Device
type
Limits
1-8
Min
9 - 22
1-8
9 - 22
1-8
-10
-100
-200
-300
9 - 22
1-8
9 - 22
All 60
Max
10
100
-200
-300
375
450
550
450
500
800
250
250
400
350
450
600
All 60
All
03, 04, 5
07
All
All
All
30
45
60
60
Unit
µA
µA
ns
ns
dB
dB
mV
ns
pF
pF
pF
1/ The listed resistance limits correspond to the following voltage values:
45 and 75 Ω − ±9.25 V, ±6.75 V
50 and 150 - ±8.50 V, ±6.0 V
2/ If not tested, shall be guaranteed to the limits specified in table I herein.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
H
81006
SHEET
6

6 Page









81006 pdf, datenblatt
TABLE II. Electrical test requirements.
MIL-STD-883 test requirements
Interim electrical parameters
(method 5004)
Final electrical test parameters
(method 5004)
Group A test requirements
(method 5005)
Groups C and D end-point
electrical parameters
(method 5005)
Subgroups
(in accordance with
MIL-STD-883, method 5005,
table I)
----
1*, 2, 3
1, 2, 3, 9, 10, 11
1
* PDA applies to subgroup 1.
4.3.2 Groups C and D inspections.
a. End-point electrical parameters shall be as specified in table II herein.
b. Steady-state life test conditions, method 1005 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit
shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent
specified in test method 1005 of MIL-STD-883.
(2) TA = +125°C, minimum.
(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-
prepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for
the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus when a system application
requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for
coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962)
should contact DSCC-VA, telephone (614) 692-0544.
6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43216-5000, or telephone
(614) 692-0547.
6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MIL-
HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted
by DSCC-VA.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
SIZE
A
REVISION LEVEL
H
81006
SHEET
12
DSCC FORM 2234
APR 97

12 Page





SeitenGesamt 15 Seiten
PDF Download[ 81006 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
81006High Level Analog Switches With Drivers/ Monolithic SiliconMaxim Integrated
Maxim Integrated

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche