|
|
PDF BU8872 Data sheet ( Hoja de datos )
| Número de pieza | BU8872 | |
| Descripción | DTMF receiver for telephones | |
| Fabricantes | ROHM Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de BU8872 (archivo pdf) en la parte inferior de esta página. Total 10 Páginas | ||
|
No Preview Available !
Communication ICs
DTMF receiver for telephones
BU8872 / BU8872FS
The BU8872 and BU8872FS are DTMF receiver ICs developed for use in telephone answering machines, and convert
16 different types of DTMF signals into 4-bit binary serial data. In addition to a compact 8-pin DIP (BU8872) or 16-pin
SSOP (BU8872FS) package, these receivers feature a wide dynamic range, eliminating the need for an external input
amplifier. Expertise from a number of companies has been incorporated into these products to enable guard time control
through a host microcomputer.
FApplications
Telephone answering machines
FFeatures
1) Dynamic range of 45dB. (internal AGC)
2) 4-bit binary serial data output.
3) Guard time can be controlled through host micro-
computer.
4) Input pins equipped with hysteresis. (ACK pin)
5) 4.19MHz ceramic resonator or crystal resonator can
be used.
6) 8-pin DIP package. (BU8872)
16-pin SSOP package. (BU8872FS)
FBlock diagram
192
1 page  
Communication ICs
FCircuit operation
A DTMF signal is supplied to the INPUT pin and applied
to a pair of 6th-order bandpass filters, which separate the
DTMF signal into its high (COL) and low (ROW) frequen-
cies. The separated tones are converted into square
waves and fed to a digital detector. (See the block dia-
gram.)
The digital detector checks the two tones to see if they
are within the valid DTMF frequency bands. If they are,
it sends a DETECT signal to the steering circuit, and
sends the appropriate column and row address signals
to a code converter.
The code converter encodes the received and detected
DTMF signal, and outputs an ENABLE signal to the
steering circuit.
Based on the DETECT and ENABLE signals, the steer-
ing circuit outputs an Early Steering (ESt) signal, which
sets the ESt pin to HIGH, indicating that a valid DTMF
signal has been detected.
If a series of pulses is input at the ACK pin while ESt is
HIGH, a decoded DTMF signal is output to the SD pin as
a binary code. (See Figure 2 for the overall timing.)
If a pulse sequence is input at the ACK pin, the data is
latched at the rising edge of the first pulse by a parallel-
serial converter, and at the same time, the LSB is output
from the SD pin. Following this, three bits of data are out-
put from the SD pin for each bit of each pulse in the pulse
sequence input from the ACK pin. As a result, a total of
four bits of data are output for the four pulses. (See Fig-
ure 3 for the ACK and SD timing.)
If the pulse sequence input to the ACK pin consists of
three or fewer pulses, the next DTMF input cannot be de-
coded properly. Any ACK pulses in excess of four are ig-
nored until ESt goes HIGH again.
Table 1 shows the format of serial data output from the
SD pin.
BU8872 / BU8872FS
196
5 Page | ||
| Páginas | Total 10 Páginas | |
| PDF Descargar | [ Datasheet BU8872.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| BU8871F | DTMF receiver for telephones | ROHM Semiconductor |
| BU8872 | DTMF receiver for telephones | ROHM Semiconductor |
| BU8872FS | DTMF receiver for telephones | ROHM Semiconductor |
| BU8874 | DTMF receiver for telephones | ROHM Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |