Datenblatt-pdf.com


TJA1050 Schematic ( PDF Datasheet ) - NXP Semiconductors

Teilenummer TJA1050
Beschreibung High speed CAN transceiver
Hersteller NXP Semiconductors
Logo NXP Semiconductors Logo 




Gesamt 16 Seiten
TJA1050 Datasheet, Funktion
INTEGRATED CIRCUITS
DATA SHEET
TJA1050
High speed CAN transceiver
Preliminary specification
File under Integrated Circuits, IC18
1999 Sep 27






TJA1050 Datasheet, Funktion
Philips Semiconductors
High speed CAN transceiver
Preliminary specification
TJA1050
CHARACTERISTICS
VCC = 4.75 to 5.25 V; Tamb = 40 to +125 °C; RL = 60 unless specified otherwise; all voltages are referenced to GND
(pin 2); positive currents flow into the IC; all parameters are guaranteed over the ambient temperature range by design,
but only 100% tested at Tamb = 25 °C unless specified otherwise.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Supply (VCC)
ICC supply current
Transmitter data input (TXD)
dominant; VTXD = 0 V tbf
recessive; VTXD = VCC tbf
75 mA
13 mA
VIH HIGH-level input voltage
VIL LOW-level input voltage
IIH HIGH-level input current
IIL LOW-level input current
Ci(TXD)
TXD input capacitance
Mode select input (S)
output recessive
output dominant
VTXD = VCC
VTXD = 0 V
not tested
2.0
0.3
30
100
0
200
VCC + 0.3
+0.8
+30
300
tbf
V
V
µA
µA
pF
VIH HIGH-level input voltage
VIL LOW-level input voltage
IIH HIGH-level input current
IIL LOW-level input current
Receiver data output (RXD)
silent mode
high speed mode
VS = VCC
VS = 0 V
2.0
0.3
30 60
30 0
VCC + 0.3
+0.8
100
+30
V
V
µA
µA
IOH HIGH-level output current
IOL LOW-level output current
Vref
Vref reference output voltage
Bus lines (CANH; CANL)
VRXD = 0.7 VCC
VRXD = 0.45 V
tbf tbf
2 8.5
50 µA < IVref < 50 µA 0.45VCC 0.5VCC
tbf mA
20 mA
0.55VCC V
VCANH(reces);
VCANL(reces)
Io(CANH)(reces);
Io(CANL)(reces)
recessive bus voltage
recessive output current
Vo(CANH)
Vo(CANL)
Vi(dif)(bus)
CANH dominant output
voltage
CANL dominant output
voltage
differential bus input voltage
(VCANH VCANL)
Io(sc)(CANH)
Io(sc)(CANL)
CANH short-circuit output
current
CANL short-circuit output
current
VTXD = VCC; no load
27 V < VCANH,
VCANL < 32 V;
0 V < VCC < 5.25 V
VTXD = 0 V
VTXD = 0 V;
42.5 < RL < 60
(dominant)
VTXD = VCC; no load
(recessive)
VCANH = 0 V;
VTXD = 0 V
VCANL = 36 V;
VTXD = 0 V
2.0
2.5
2.8
0.5
1.5
500
35
35
3.0 V
+2.5 mA
4.5 V
2.0 V
3.0 V
+50 mV
95 mA
150 mA
1999 Sep 27
6

6 Page









TJA1050 pdf, datenblatt
Philips Semiconductors
High speed CAN transceiver
Preliminary specification
TJA1050
SOLDERING
Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering is not always suitable
for surface mount ICs, or for printed-circuit boards with
high population densities. In these situations reflow
soldering is often used.
Reflow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
infrared/convection heating in a conveyor type oven.
Throughput times (preheating, soldering and cooling) vary
between 100 and 200 seconds depending on heating
method.
Typical reflow peak temperatures range from
215 to 250 °C. The top-surface temperature of the
packages should preferable be kept below 230 °C.
Wave soldering
Conventional single wave soldering is not recommended
for surface mount devices (SMDs) or printed-circuit boards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is preferred to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
For packages with leads on four sides, the footprint must
be placed at a 45° angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time is 4 seconds at 250 °C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300 °C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320 °C.
1999 Sep 27
12

12 Page





SeitenGesamt 16 Seiten
PDF Download[ TJA1050 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
TJA1050High speed CAN transceiverNXP Semiconductors
NXP Semiconductors
TJA1050THigh speed CAN transceiverNXP Semiconductors
NXP Semiconductors
TJA1050UHigh speed CAN transceiverNXP Semiconductors
NXP Semiconductors
TJA1051High-speed CANtransceiverNXP Semiconductors
NXP Semiconductors
TJA1053Fault-tolerant CAN transceiverNXP Semiconductors
NXP Semiconductors

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche