|
|
PDF TZA1026 Data sheet ( Hoja de datos )
| Número de pieza | TZA1026 | |
| Descripción | Data amplifier and laser supply circuit for CD audio and video optical systems ADALASAuto | |
| Fabricantes | NXP Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TZA1026 (archivo pdf) en la parte inferior de esta página. Total 20 Páginas | ||
|
No Preview Available !
INTEGRATED CIRCUITS
DATA SHEET
TZA1026
Data amplifier and laser supply
circuit for CD audio and video
optical systems (ADALASAuto)
Product specification
File under Integrated Circuits, IC01
1998 Oct 30
1 page  
Philips Semiconductors
Data amplifier and laser supply circuit for CD
audio and video optical systems (ADALASAuto)
Product specification
TZA1026
PINNING
SYMBOL PIN
DESCRIPTION
LD 1 current output to laser diode
VDD(L)
CFIL
2 laser supply voltage
3 external filter capacitor
MON
4 laser monitor diode input
DIN 5 central diode input
GND
6 ground
PWRON 7 power-on select input
CMFB
8 common mode feedback voltage
input
RFFB
9 external RF feedback resistor
RFEQO 10 RF amplifier output
CDRW
11 gain select input for CD-A/V, CD-R/W
EQSEL
12 equalizer/speed select input
(n = 1, 2 or 4)
VDD
RGADJ
13 supply voltage
14 external laser supply gain adjust
resistor
handbook, halfpage
LD 1
VDD(L) 2
CFIL 3
MON 4
DIN 5
GND 6
PWRON 7
14 RGADJ
13 VDD
12 EQSEL
TZA1026 11 CDRW
10 RFEQO
9 RFFB
8 CMFB
MBK890
The gain of the RF amplifier can be adjusted by the
external input resistors. Fig.3 shows the simplified
schematic which can be used to determine the RF gain.
The signal is AC coupled to the RF amplifier. The formula
to determine the gain is shown below:
GRF = –n × Z----t--Rr---(--R2---F---)-
(1)
where:
GRF is the RF amplifier gain
n is the number of input resistors
Ztr(RF) is the transimpedance of the amplifier (Ω)
R2 is the value of the input resistors(Ω).
The gain can be increased by a factor 4 by making
pin CDRW HIGH. The value of Ztr(RF) is 9.8 kΩ for CD-A/V
(CDRW = LOW) and 38 kΩ for CD-R/W (CDRW = HIGH).
The equalizer/bandwidth section can be switched between
n = 1, n = 2 (inclusive the corresponding equalizer) or
n = 4 (inclusive the required bandwidth limitation) times
speed.
The DC output level of the amplifier can be set by applying
a DC voltage on the common mode feedback pin CMFB.
Since the input signal is AC-coupled the RF output voltage
will swing (symmetrically) around this DC level.
The coupling of the TZA1026 to the signal processor
(SAA7326) can be either AC or DC. When an AC-coupling
is chosen (see Fig.8) the minimum supply voltage can be
applied. When a DC-coupling is chosen (see Fig.9) a
minimum supply voltage of 2.8 V is required.
Fig.2 Pin configuration.
FUNCTIONAL DESCRIPTION
The TZA1026 consists of two sections, the RF amplifier
and the automatic laser power control circuit.
RF amplifier
The RF amplifier consists of a current input amplifier, an
equalizer/bandwidth section and a transimpedance output
amplifier with an external feedback resistor of 10 kΩ (fixed
value).
handbook, halfpage
Vin
Vin
Vin
R2(1)
R2(2) C2
10 kΩ
R2(n)
CDRW
RFEQO
MGL530
Fig.3 Simplified schematic.
1998 Oct 30
5
5 Page 
Philips Semiconductors
Data amplifier and laser supply circuit for CD
audio and video optical systems (ADALASAuto)
Product specification
TZA1026
handbook,1h2alfpage
G
(dB)
8
4
(2)
(1)
MGR520
254
td
(ns)
252
250
handbook,1h2alfpage
G
(dB)
8
4
MGR521
132
(2)
td
(ns)
130
(1)
128
0 248 0 126
−4
10−1
246
1
f (MHz)
10
(1) Gain.
(2) Delay.
Definition of delay: td = ----3-------ϕ-6-f-----0-------
Fig.5 Equalizer gain and delay for n = 1.
handbook, h2alfpage
G
(dB)
0
−2
MGR522
47
td
(ns)
45
(1)
(2)
43
−4
10−1
124
1 f (MHz) 10
(1) Gain.
(2) Delay.
Definition of delay: td = ----3-------ϕ-6-f-----0-------
Fig.6 Equalizer gain and delay for n = 2.
Table 1 Recommended values of component per speed
for application diagram of Figs 8 and 9
n C1
1 47 pF
2 22 pF
4 10 pF
−4
10−1
41
1
f (MHz)
10
(1) Gain.
(2) Delay.
Definition of delay: td = ----3-------ϕ-6-f-----0-------
Fig.7 Gain and delay for n = 4.
1998 Oct 30
11
11 Page | ||
| Páginas | Total 20 Páginas | |
| PDF Descargar | [ Datasheet TZA1026.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TZA1020 | Pre-amplifiers for CD-RW systems | NXP Semiconductors |
| TZA1020A | Pre-amplifiers for CD-RW systems | NXP Semiconductors |
| TZA1020HP | Pre-amplifiers for CD-RW systems | NXP Semiconductors |
| TZA1022 | Preamplifier and Laser Supply for CD/CDW Read-Only Optical Systems |  Philips |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |