|
|
Número de pieza | V14MLN41206 | |
Descripción | Multiline Transient Voltage Surge Suppressor | |
Fabricantes | Littelfuse | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de V14MLN41206 (archivo pdf) en la parte inferior de esta página. Total 7 Páginas | ||
No Preview Available ! Next
MLN SurgeArray™ Suppressor
The MLN SurgeArray™ Suppressor is designed to help protect compo-
nents from transient voltages that exist at the circuit board level. This
device provides four independent suppressors in a single “1206” leadless
chip in order to reduce part count and placement time as well as save
space on printed circuit boards.
SurgeArray™ devices are intended to suppress ESD, EFT and other
transients in order to protect integrated circuits or other sensitive
components operating at any voltage up to 18VDC. SurgeArray devices
are rated to the IEC 61000-4-2 human body model ESD to help products
attain EMC compliance. The array offers excellent isolation and low
crosstalk between sections.
The inherent capacitance of the SurgeArray Suppressor permits it to
function as a filter/suppressor, thereby replacing separate zener/
capacitor combinations.
The MLN array is manufactured using the Littelfuse Multilayer technology
process and is similar to the Littelfuse ML and MLE Series of discrete
leadless chips.
The MLN can also be provided in a Dual version. Contact Littelfuse
for information.
Features
• Four Individual Devices in One 1206 Chip
• ESD Rated to IEC 61000-4-2 (Level 4)
• AC Characterized for Impedance and Capacitance
• Low Adjacent Channel Crosstalk, -55dB at 10MHz (Typ)
• Low Leakage (6nA at 5.5V, 30nA at 15V)
• Operating Voltage up to 18VM(DC)
• -55oC to 125oC Operating Temperature Range
• Low-Profile, PCMCIA Compatible
Applications
• Data, Diagnostic I/O Ports
• Analog Signal/Sensor Lines
• Portable/Hand-Held Products
• Mobile Communications/Cellular Phones
• Computer/DSP Products
• Industrial Instruments Including Medical
Previous
Surface Mount Varistors
Multiline Transient Voltage Surge Suppressor
3
www.littelfuse.com
151
1 page Next
Previous
Surface Mount Varistors
Multiline Transient Voltage Surge Suppressor
MLN SurgeArray™ Suppressor
Typical Performance Curves Any Single Section (Continued)
10000
1000
100
10 3
1
0.1
1MHz
10MHz
100MHz
FREQUENCY
FIGURE 10. IMPEDANCE vs FREQUENCY
1GHz
10GHz
0
-20
-40
-60
-80
-100
-120
1kHz
VIN = 1VRMS
Z = 50Ω
10kHz
100kHz
1MHz
FREQUENCY
10MHz
FIGURE 11. ADJACENT CHANNEL CROSSTALK
100MHz
1GHz
Soldering Recommendations
The principal techniques used for the soldering of components in surface
mount technology are Infrared (IR) Reflow, Vapour Phase Reflow, and
Wave Soldering. Typical profiles are shown in Figures 12, 13 and 14.
When wave soldering, the MLN suppressor is attached to the circuit
board by means of an adhesive. The assembly is then placed on a con-
veyor and run through the soldering process to contact the wave. With IR
and Vapour Phase Reflow, the device is placed in a solder paste on the
substrate. As the solder paste is heated, it reflows and solders the unit to
the board.
The recommended solder for the MLN suppressor is a 62/36/2
(Sn/Pb/Ag), 60/40 (Sn/Pb), or 63/37 (Sn/Pb). Littelfuse also
recommends an RMA solder flux.
Wave soldering is the most strenuous of the processes. To avoid the
possibility of generating stresses due to thermal shock, a preheat stage
in the soldering process is recommended, and the peak temperature of
the solder process should be rigidly controlled.
When using a reflow process, care should be taken to ensure that the
MLN chip is not subjected to a thermal gradient steeper than 4 degrees
per second; the ideal gradient being 2 degrees per second. During the
soldering process, preheating to within 100 degrees of the solders peak
temperature is essential to minimize thermal shock. Examples of the sol-
dering conditions for the MLN array of suppressors are given in the
tables below.
Once the soldering process has been completed, it is still necessary to
ensure that any further thermal shocks are avoided. One possible cause of
thermal shock is hot printed circuit boards being removed from the solder
process and subjected to cleaning solvents at room temperature. The
boards must be allowed to gradually cool to less than 50oC before cleaning.
www.littelfuse.com
155
5 Page |
Páginas | Total 7 Páginas | |
PDF Descargar | [ Datasheet V14MLN41206.PDF ] |
Número de pieza | Descripción | Fabricantes |
V14MLN41206 | Multiline Transient Voltage Surge Suppressor | Littelfuse |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |