|
|
Número de pieza | LXM1612-12-03 | |
Descripción | 12V Highly-Integrated/ Digital Dimming CCFL Inverter Module | |
Fabricantes | Microsemi Corporation | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de LXM1612-12-03 (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
No Preview Available ! A MICROSEMI COMPANY
LXM1612-12-xx
12V Highly-Integrated, Digital Dimming CCFL Inverter Module
PRELIMINARY DATASHEET
RangeMAX Wide Range Dimming,
Single Output Inverter. The LXM1612-
12-xx series of Direct Drive™ CCFL
(Cold Cathode Fluorescent Lamp)
Inverter Modules are specifically
designed for driving LCD backlight
lamps.
RangeMAX Digital Dimming
Technique. Digital Dimming provides
flicker-free brightness control in any
wide-range dimming application.
The modules are equipped with a
dimming input that permits brightness
control from either an external
potentiometer, DC voltage source, or
PWM signal. The resultant “burst drive”
that energizes the lamp was designed
specifically to ensure that no premature
lamp degradation occurs.
Input Voltage Range. The modules
convert DC voltage from the system
battery or AC adapter directly to high-
frequency, high-voltage waves required
to ignite and operate CCFL lamps. A 5V
input inverter is also available
(LXM1612-05-xx).
Direct Drive Technology. The module
design is based on a new Direct Drive
topology, which provides a number of
cost and performance advantages.
Additional Features. Other benefits of
this new topology are fixed-frequency
operation and secondary-side strike-
voltage regulation and all LXM1612-12-
xx modules feature both open and
shorted lamp protection.
IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com
DC Voltage
Source
Potentiom eter
PW M
Signal
BRITE
RangeMAX Wide Range
Dimming
9.6V to 14.4V Input Voltage
Fully Integrated Direct Drive
And Dimming Control
Single Sided PCB Layout
Easy To Use Brightness
Control
MicroAmp SLEEP Mode
Output Short-Circuit
Protection And Automatic
Strike-Voltage Regulation
Fixed Frequency Operation
Notebook And Sub-Notebook
Computers
Portable Instrumentation
Desktop Displays
Low Ambient Light
Conditions (i.e. Aircraft
Cabins, Automobile)
Smooth, Flicker Free 1-100%
Full-Range Brightness
Control Gives Your Product
A High Quality Image
Output Open Circuit Voltage
Regulation Minimizes
Corona Discharge For Long
Life And High Reliability
Power Efficient. “Low
Brightness” Capability Allows
For Advanced Power
Management
PART NUMBER
LXM1612-12-01
LXM1612-12-02
LXM1612-12-03
OUTPUT CONNECTOR
JST SM02(8.0)B-BHS-1-TB
JST SM02B-BHSS-1-TB
Honda QZ-19-A3MYL #02
INVERTER MATES DIRECTLY
TO PANEL CONNECTORS
BHR-03VS-1
BHSR-02VS-1
QZ-19-3F01
Copyright © 2000
Rev. 0.3f, 2000-12-06
Microsemi
Linfinity Microelectronics Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 1
1 page A MICROSEMI COMPANY
LXM1612-12-xx
12V Highly-Integrated, Digital Dimming CCFL Inverter Module
PRELIMINARY DATASHEET
Integrated brightness control circuit includes a DC voltage to In applications with no access to a vertical sync., an onboard
pulse width converter that minimizes system design work and
oscillator operates the inverter burst rate at about 250Hz. In
system noise susceptibility. This provides a familiar and
this non-synchronous mode, minor display disturbances can
convenient interface while reducing the potential for
be found under certain video conditions. This performance
externally induced noise, which can cause lamp flicker.
may be acceptable for many applications, but
RangeMAX inverter modules are designed to operate with the
burst frequency synchronized to the video frame rate. This
synchronization must be used when no disturbance can be
tolerated.
provides operation with no visible display disturbances A single input will accommodate negative and positive
caused by beat frequencies between the lamps and video
vertical sync pulses at any pulse width.
frame rates. In this synchronous mode, the inverter burst rate Separate feedback loops for lamp current and open circuit
operates at twice the video refresh rate, well beyond standard
voltage regulation insure reliable strike under all operating
50/60Hz video refresh rates where the eye can perceive
conditions, automatic over-voltage prevention with broken
pulsing light.
or failed lamps, and accurate lamp current regulation.
12V
DAC or
Pot
10k
BRITE
V IN1
V
HI
LXM1612-12-xx
R
5V
BRITE RTN
SLEEP VSYNC
V LO
GND
0V
V SYN C
CCFL
TUBE
Figure 5 - Potentiometer Brightness Control
PW M Signal
from System
BRITE
P.W .
< 2ms
LXM1612-12-xx
0 < P.W. < 100% of perio d
Figure 5A - PW M Brightness Control
The brightness control may be a voltage output DAC, digital
resistor or a simple 10k potentiometer. If desired, an
additional series resistor with the 10k potentiometer can be
used to set a higher minimum brightness setting as shown in
Figure 5. A 2.5V to 5V Logic Level PWM signal from a
micro-controller may also be used as shown in Figure 5A.
If synchronization to the video frame rate is desired, connect
the vertical sync pulse from the system video controller to
the VSYNC input. If no video synchronization is desired,
connect VSYNC to ground.
If you need to turn the inverter ON/OFF remotely, connect
to 2.5V to 5V logic signal to the SLEEP input.
Connect VHI to high voltage wire from the lamp. Connect
VLO to the low voltage wire (wire with thinner insulation).
Never connect VLO to circuit ground as this will defeat lamp
current regulation. If both lamp wires have heavy high
voltage insulation, connect the longest wire to VLO. This
wire is typically white.
&'
(
The LXM1612-05 output current can be adjusted by changing the
value of two resistors on the PCB. The following table shows the
approximate new output current values:
Output Current
7.0mA
6.0mA
5.8mA
5.0mA
4.0mA
3.0mA
R12
2.00K 1%
2.61K 1%
2.74K 1%
2.74K 1%
2.74K 1%
2.74K 1%
R16
Not Used
Not Used
Not Used
499K 1%
178K 1%
78.7K 1%
R30
U4
R21
C7
R20
R41
R33 R34
R4 R3
C3
C4
R2
C5
C21
R38
R39
C6 C8
R5
R6
C9
C2
U1
R7 R15
C11 R12 R14
C15
C16
C12
R11
C14
C13
R16
R10
C10
R13
-
Component Replacement Locations
Copyright © 2000
Rev. 0.3f, 2000-12-06
Microsemi
Linfinity Microelectronics Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 5
5 Page |
Páginas | Total 6 Páginas | |
PDF Descargar | [ Datasheet LXM1612-12-03.PDF ] |
Número de pieza | Descripción | Fabricantes |
LXM1612-12-01 | 12V Highly-Integrated/ Digital Dimming CCFL Inverter Module | Microsemi Corporation |
LXM1612-12-02 | 12V Highly-Integrated/ Digital Dimming CCFL Inverter Module | Microsemi Corporation |
LXM1612-12-03 | 12V Highly-Integrated/ Digital Dimming CCFL Inverter Module | Microsemi Corporation |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |