|
|
PDF LS027B7DH01 Data sheet ( Hoja de datos )
| Número de pieza | LS027B7DH01 | |
| Descripción | LCD Module | |
| Fabricantes | Sharp | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LS027B7DH01 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
1 page  
SPEC No.
MODEL No.
LCP-2110015A
LS027B7DH01
PAGE
3
z Equipment and containers
Process equipment such as conveyer, soldering iron, working bench and containers may possibly generate
electrostatic charge up and discharge. Equipment must be grounded through 100Mohms resistance. Use
ion blower.
z Floor
Floor plays an important role in leaking static electricity generated in human body or equipment. If the floor
is made of insulated material (such as polymer or rubber material), such static electricity may charge.
Proper measure should be taken to avoid static electricity charge (electrostatic earth: 100Mohms).There is
a possibility that the static electricity is charged to them without leakage in case of insulating floor, so the
electrostatic earth:1×108ȍ should be made.
z Humidity
Humidity in work area relates to surface resistance of the persons or objects that generate
electrostatics, and it can be manipulated to prevent electrostatic charge. Humidity of 40% or
lower increases electrostatic earth resistance and promotes electrostatic charging. Therefore,
the humidity in the work area should be kept above 40%. Specifically for film peeling process
or processes that require human hands, humidity should be kept above 50% and use electricity
removal blower.
z Transportation/Storage
Containers and styroform used in transporation and storage may charge electrostatic (from friction and
peeling) or electrostatic charge from human body, etc. may cause containers and styroform to have induced
charge. Proper electrostatic measure should be taken for containers and storage material.
5 Page 
SPEC No.
MODEL No.
LCP-2110015A
LS027B7DH01
PAGE
9
5䋮Absolute Maximum Rating
Table 5-1㩷 䋨GND䋽0V䋩
Item
Code
MIN.
MAX.
Unit
Remark
Power
Analog Power Supply
VDDA -0.3 䋫5.8
V
supply
Voltage
Logic Power Supply
VDD -0.3 䋫5.8
V 䇼Remark 5-1䇽
Input signal terminal voltage (high)
VDD
V 䇼Remark 5-2䇽
Input signal terminal voltage (low)
-0.3 V
Storage temperature
Tstg -30 䋫80
㷄 䇼Remark 5-3,4䇽
Operating temperature
Topr1
-20
䋫70
㷄 䇼Remark 5-5䇽
(Panel surface temperature)
㩷 䇼Remark 5-1䇽 Also applicable to EXTMODE.
䇼Remark 5-2䇽 Applicable to SCLK, SI, SCS, DISP, EXTCOMIN.
䇼Remark 5-3䇽 Do not exceed this rating in any area of the module.
䇼Remark 5-4䇽 Maximum wet-bulb temperature should be 57㷄 or lower. Do not allow condensation.
Condensation may cause electrical leak and the module may not meet s specification.
䇼Remark 5-5䇽Operating temperature is temperature that guarantess operation only. For contrast, response speed, and
other display quty, module is evaluated at Ta=+25͠.
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet LS027B7DH01.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LS027B7DH01 | LCD Module | Sharp |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |