|
|
PDF LS044Q7DH01 Data sheet ( Hoja de datos )
| Número de pieza | LS044Q7DH01 | |
| Descripción | Technical Literature for LCD Module | |
| Fabricantes | Sharp | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LS044Q7DH01 (archivo pdf) en la parte inferior de esta página. Total 29 Páginas | ||
|
No Preview Available !
No.
Date
LCP2111038A
Aug 11, 2011
Technical Literature
For
TFT-LCD Module
Model No. LS044Q7DH01
Notice
The technical Literature is subject to change without any
prior notice for the purpose of product improvement.
Please contact Sharp or its representative before designing
your product based on this literature.
Display Device Business Group
SHARP CORPORATION
1 page  
SPEC No.
MODEL No.
LCP2111038A
LS044Q7DH01
PAGE
3
z Equipment and containers
Process equipment such as conveyer, soldering iron, working bench and containers may possibly generate
electrostatic charge up and discharge. Equipment must be grounded through 100Mohms resistance. Use
ion blower.
z Floor
Floor plays an important role in leaking static electricity generated in human body or equipment. If the floor
is made of insulated material (such as polymer or rubber material), such static electricity may charge.
Proper measure should be taken to avoid static electricity charge (electrostatic earth: 100Mohms).There is
a possibility that the static electricity is charged to them without leakage in case of insulating floor, so the
electrostatic earth:1×108Ω should be made.
z Humidity
Humidity in work area relates to surface resistance of the persons or objects that generate electrostatics,
and it can be manipulated to prevent electrostatic charge. Humidity of 40% or lower increases electrostatic
earth resistance and promotes electrostatic charging. Therefore, the humidity in the work area is
recommended to be kept above 40%. Specifically for film peeling process or processes that require human
hands, humidity is recommended to be kept above 50% and use electricity removal blower.
z Transportation/Storage
Containers and styroform used in transporation and storage may charge electrostatic (from friction and
peeling) or electrostatic charge from human body, etc. may cause containers and styroform to have induced
charge. Proper electrostatic measure should be taken for containers and storage material.
5 Page 
SPEC No.
MODEL No.
LCP2111038A
LS044Q7DH01
PAGE
9
5．Absolute Maximum Rating
Table 5-1 （GND＝0V）
Item
Code
MIN.
MAX.
Unit
Remark
Power
Analog Power Supply
VDDA -0.3 ＋5.8
V
supply
Voltage
Logic Power Supply
VDD -0.3 ＋5.8
V 【Remark 5-1】
Input signal terminal voltage (high)
VDD
V 【Remark 5-2】
Input signal terminal voltage (low)
-0.3 V
Storage temperature
Tstg -30 ＋80
℃ 【Remark 5-3,4】
Operating temperature
Topr1
-20
＋70
℃ 【Remark 5-5】
(Panel surface temperature)
【Remark 5-1】 Also applicable to EXTMODE.
【Remark 5-2】 Applicable to SCLK, SI, SCS, DISP, EXTCOMIN.
【Remark 5-3】 Do not exceed this rating in any area of the module.
【Remark 5-4】 Maximum wet-bulb temperature should be 57℃ or lower. Do not allow condensation.
Condensation may cause electrical leak and the module may not meet s specification.
【Remark 5-5】Operating temperature is temperature that guarantess operation only. For contrast, response speed, and
other display quty, module is evaluated at Ta=+25℃.
11 Page | ||
| Páginas | Total 29 Páginas | |
| PDF Descargar | [ Datasheet LS044Q7DH01.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LS044Q7DH01 | Technical Literature for LCD Module | Sharp |
| LS044Q7DH01 | LCD Module | Sharp |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |