Datenblatt-pdf.com


LS013B7DH06 Schematic ( PDF Datasheet ) - Sharp

Teilenummer LS013B7DH06
Beschreibung LCD Module
Hersteller Sharp
Logo Sharp Logo 




Gesamt 30 Seiten
LS013B7DH06 Datasheet, Funktion
www.avnet-embedded.eu






LS013B7DH06 Datasheet, Funktion
SPEC No.
LD-27103A
MODEL No.
LS013B7DH06
PAGE
4
(15) To prevent reduction in optical quality and abnormal display, avoid exposure and contamination of the LCD
panel from epoxy resin (mine system curing agent) that comes out from the material and the packaging material
used for the set side, the silicon adhesive (dealcoholization system and oxime system), and the tray blowing
agents ( azo-compound), etc. Please confirm LCD panel compatibility with materials employed in your
manufacturing and shipping processes.
(16) Since the LCD panel is made of glass, it may break or crack if dropped or bumped on hard surface. Always
handle with care.
(17) Please design part arrangement to consider the heat dissipation not to change the local temperature for
module.
(18) This product is not water-proof and dust-proof structure.
(19) As this LCD module is composed electronic circuits, it is sensitive to electrostatic discharge of 200V or more.
Handle with care using cautions for the followings:
Operators
Operators must wear anti-static wears to prevent electrostatic charge up to and discharge from human
body.
Equipment and containers
Process equipment such as conveyer, soldering iron, working bench and containers may possibly
generate electrostatic charge up and discharge. Equipment must be grounded through 100Mohms
resistance. Use ion blower.
Floor
Floor plays an important role in leaking static electricity generated in human body or equipment. If the
floor is made of insulated material (such as polymer or rubber material), such static electricity may charge.
Proper measure should be taken to avoid static electricity charge (electrostatic earth: 100Mohms).There
is a possibility that the static electricity is charged to them without leakage in case of insulating floor, so
the electrostatic earth: 100Mohms should be made.
Humidity
Humidity in work area relates to surface resistance of the persons or objects that generate electrostatics,
and it can be manipulated to prevent electrostatic charge. Humidity of 40% or lower increases
electrostatic earth resistance and promotes electrostatic charging. Therefore, the humidity in the work
area should be kept above 40%. Specifically for film peeling process or processes that require human
hands, humidity should be kept above 50% and use electricity removal blower.
Transportation/Storage
Containers and styroform used in transporation and storage may charge electrostatic (from friction and
peeling) or electrostatic charge from human body, etc. may cause containers and styroform to have
induced charge. Proper electrostatic measure should be taken for containers and storage material.
www.avnet-embedded.eu

6 Page









LS013B7DH06 pdf, datenblatt
SPEC No.
LD-27103A
MODEL No.
LS013B7DH06
PAGE
10
4. Input terminal names and functions
Table4-1 Pin description
Terminal Symbol
IO
Configurations
Function
Remark
1
SCLK
INPUT
NoPull
Serial clock signal
2
SI
INPUT
NoPull
Serial data input signal
3
SCS
INPUT
NoPull
Chip select signal ( Active of Hi )
NoPull
4 EXTCOMIN INPUT
External COM inversion signal input
(Input Square wave or connect the VSS)
Note 4-2
5
DISP
INPUT
NoPull
Display ON/OFF signal
Note 4-1
6
VDDA
POWER
Power supply (Analog)
7
VDD
POWER
Power supply (Digital)
NoPull
Control mode of COM inversion is select terminal
8 EXTMODE INPUT
Note 4-2
( connect the VDD or VSS )
9
VSS
GND
GND (Digital)
10
VSSA
GND
GND (Analog)
NoPull Neither Pulled up or Pulled down.
Note 4-1The display ON/OFF signal is only for display. Data in the memory will be saved at the time of ON/OFF.
When it’s ”Hi”, data in the memory will display, when it’s ”Lo”, white color will diaplay and data in the
memory will be saved.
Note 4-2When EXTMODE is ”Hi”, EXTCOMIN signal is enable.
When EXTMODE is ”Lo” ,serial input flag is enable.
“Hi”mode ; connect the EXTMODE to VDD,
”Lo” mode ; connect the EXTMODE and EXTCOMIN to VSS.
4-1Recommended Circuit
< EXTMODE=”Lo” >
COM Signal Serial Flag nput
1 SCLK
2 SI
3 SCS
4 EXTCOMIN
5 DISP
6 VDDA
7 VDD
8 EXTMODE
9 VSS
10 VSSA
< EXTMODE=”Hi” >
External COM Signal Input
1 SCLK
2 SI
3 SCS
4 EXTCOMIN
5 DISP
6 VDDA
7 VDD
8 EXTMODE
9 VSS
10 VSSA
Figure 4-1 Recommended circuit
www.avnet-embedded.eu

12 Page





SeitenGesamt 30 Seiten
PDF Download[ LS013B7DH06 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
LS013B7DH01LCD ModuleSharp
Sharp
LS013B7DH03Application Information for LCD ModuleSharp
Sharp
LS013B7DH03LCD ModuleSharp
Sharp
LS013B7DH05LCD ModuleSharp
Sharp
LS013B7DH06LCD ModuleSharp
Sharp

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche