Datenblatt-pdf.com


IEX139BLB1 Schematic ( PDF Datasheet ) - Iexcellence

Teilenummer IEX139BLB1
Beschreibung COLOR AMOLED MODULE
Hersteller Iexcellence
Logo Iexcellence Logo 




Gesamt 24 Seiten
IEX139BLB1 Datasheet, Funktion
Version:
Page:
0.0
0
CUSTOMER APPROVAL SHEET
Company Name
MODEL
CUSTOMER
APPROVED
IEX139BLB01.0
Title :
Name :
APPROVAL FOR SPECIFICATIONS ONLY (Spec. Ver. )
APPROVAL FOR SPECIFICATIONS AND ES SAMPLE (Spec. Ver.
APPROVAL FOR SPECIFICATIONS AND CS SAMPLE (Spec. Ver.
CUSTOMER REMARK :
)
)






IEX139BLB1 Datasheet, Funktion
Version
Page:
0.0
24
B. Electrical Specifications
1. Main FPC Pin assignment — AMOLED Panel Input/Output Signal Interface
FPCA recommended connector: 504248-2410 (Molex)
Main board recommended connector: 504208-2410 (Molex)
FPC
Pin_name
I/O
Description
1
GND
P Ground
2 XRES I Device reset signal (0 : Enable ; 1: Disable )
3
DSI_D0N
I/O MIPI negative data signal
4
SWIRE
O SWIRE signal for PWR IC control
5
DSI_D0P
I/O MIPI positive data signal
6 NC - Flaoting
7
GND
P Ground
Vsync(vertical sync)signal output from panel to avoid
8 TE I
tearing effect
9
DSI_CLKN
I MIPI negative clock signal
10 GND P Ground
11 DSI_CLKP I MIPI positive clock signal
12 GND P Ground
13 GND P Ground
14 GND P Ground
15 VDDIO P Power supply for Interface system excep MIPI interface
16 VCI P Driver analog power supply
17 GND P Ground
18 GND P Ground
19 ELVSS P AMOLED negative power supply
20 ELVDD P AMOLED positive power supply
21 ELVSS P AMOLED negative power supply
22 ELVDD P AMOLED positive power supply
23 ELVSS P AMOLED negative power supply
24 ELVDD P AMOLED positive power supply
Note: I = input ; O = output ; P = Power ; I/O = input / Output
5

6 Page









IEX139BLB1 pdf, datenblatt
2. Display RESET Timing Characteristics
Reset input timing
Version
Page:
0.0
24
IOVDD=1.65 to 1.95V, VDD=2.8 to 3.1V, AGND=DGND=0V, Ta=-40 to 85
Timing Parameters
Symbol
Parameter
tRESW *1) Reset low pulse width
tREST *2) Reset complete time
Related
Pins
RESX
-
-
MIN TYP MAX
Note
Unit
10 -
-
- µs
--
5
When reset applied
during Sleep in mode
ms
When reset applied
- 120
during Sleep out
ms
mode
Note 1. Spike due to an electrostatic discharge on RESX line does not cause irregular system reset
according to the table below.
RESX Pulse
Shorter than 5µs
Longer than 15µs
Between 5µs and
15µs
Action
Reset Rejected
Reset
Reset starts
(It depends on voltage and temperature condition.)
Note 2. During the resetting period, the display will be blanked (The display is entering blanking
sequence, which maximum time is 120 ms, when Reset Starts in Sleep Out –mode. The display
remains the blank state in Sleep In –mode) and then return to Default condition for H/W reset.
Note 3. During Reset Complete Time, data in OTP will be latched to internal register during this period.
This loading is done every time when there is H/W reset complete time (tREST) within 5ms after a
rising edge of RESX.
Note 4. Spike Rejection also applies during a valid reset pulse as shown below:
11

12 Page





SeitenGesamt 24 Seiten
PDF Download[ IEX139BLB1 Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
IEX139BLB01.0COLOR AMOLED MODULEIexcellence
Iexcellence
IEX139BLB1COLOR AMOLED MODULEIexcellence
Iexcellence

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche