PDF MB85RS16N Data sheet ( Hoja de datos )

Número de pieza	MB85RS16N
Descripción	16K (2K x 8) Bit SPI
Fabricantes	Fujitsu
Logotipo
Hay una vista previa y un enlace de descarga de MB85RS16N (archivo pdf) en la parte inferior de esta página. Total 30 Páginas
No Preview Available ! FUJITSU SEMICONDUCTOR DATA SHEET Memory FRAM DS501-00030-3v0-E 16 K (2 K × 8) Bit SPI MB85RS16N ■ DESCRIPTION MB85RS16N is a FRAM (Ferroelectric Random Access Memory) chip in a configuration of 2,048 words × 8 bits, using the ferroelectric process and silicon gate CMOS process technologies for forming the nonvolatile memory cells. MB85RS16N adopts the Serial Peripheral Interface (SPI). The MB85RS16N is able to retain data without using a back-up battery, as is needed for SRAM. The memory cells used in the MB85RS16N can be used for 1010 read/write operations, which is a significant improvement over the number of read and write operations supported by Flash memory and E2PROM. MB85RS16N does not take long time to write data like Flash memories or E2PROM, and MB85RS16N takes no wait time. ■ FEATURES • Bit configuration : 2,048 words × 8 bits • Serial Peripheral Interface : SPI (Serial Peripheral Interface) Correspondent to SPI mode 0 (0, 0) and mode 3 (1, 1) • Operating frequency : 20 MHz (Max) • High endurance : 1010 Read/Writes per byte ( + 95 °C) 1012 Read/Writes per byte ( + 85 °C) • Data retention : 10 years ( + 95 °C), 95 years ( + 55 °C), over 200 years ( + 35 °C) • Operating power supply voltage : 2.7 V to 3.6 V • Low power consumption : Operating power supply current 1.5 mA (Typ@20 MHz) Standby current 5 μA (Typ@+25 °C) • Operation ambient temperature range : − 40 °C to + 95 °C • Package : 8-pin plastic SOP (FPT-8P-M02) 8-pin plastic SON (LCC-8P-M04) RoHS compliant Copyright 2014-2015 FUJITSU SEMICONDUCTOR LIMITED 2015.6 1 page MB85RS16N ■ SERIAL PERIPHERAL INTERFACE (SPI) MB85RS16N works as a slave of SPI. More than 2 devices can be connected by using microcontroller equipped with SPI port. By using a microcontroller not equipped with SPI port, SI and SO can be bus connected to use. SCK MOSI MISO SPI Microcontroller SS1 SO SI SCK MB85RS16N CS HOLD SO SI SCK MB85RS16N CS HOLD SS2 HOLD1 HOLD2 System Configuration with SPI Port MOSI : Master Out Slave In MISO : Master In Slave Out SS : Slave Select Microcontroller SO SI SCK MB85RS16N CS HOLD System Configuration without SPI Port DS501-00030-3v0-E 5 5 Page MB85RS16N ■ BLOCK PROTECT Writing protect block for WRITE command is configured by the value of BP0 and BP1 in the status register. BP1 BP0 Protected Block 0 0 None 0 1 600H to 7FFH (upper 1/4) 1 0 400H to 7FFH (upper 1/2) 1 1 000H to 7FFH (all) ■ WRITING PROTECT Writing operation of the WRITE command and the WRSR command are protected with the value of WEL, WPEN, WP as shown in the table. WEL WPEN WP Protected Blocks Unprotected Blocks Status Register 0XX Protected Protected Protected 10X Protected Unprotected Unprotected 110 Protected Unprotected Protected 111 Protected Unprotected Unprotected ■ HOLD OPERATION Hold status is retained without aborting a command if HOLD is the “L” level while CS is the “L” level. The timing for starting and ending hold status depends on the SCK to be the “H” level or the “L” level when a HOLD pin input is transited to the hold condition as shown in the diagram below. In case the HOLD pin transited to “L” level when SCK is “L” level, return the HOLD pin to “H” level at SCK being “L” level. In the same manner, in case the HOLD pin transited to “L” level when SCK is “H” level, return the HOLD pin to “H” level at SCK being “H” level. Arbitrary command operation is interrupted in hold status, SCK and SI inputs become don’t care. And, SO becomes High-Z while reading command (RDSR, READ). If CS is rising during hold status, a command is aborted. In case the command is aborted before its recognition, WEL holds the value before transition to hold status. CS SCK HOLD Hold Condition Hold Condition DS501-00030-3v0-E 11 11 Page

Páginas	Total 30 Páginas
PDF Descargar	[ Datasheet MB85RS16N.PDF ]

Hoja de datos destacado

Número de pieza	Descripción	Fabricantes
MB85RS16	16K (2K x 8) Bit SPI	Fujitsu
MB85RS16N	16K (2K x 8) Bit SPI	Fujitsu

Número de pieza	Descripción	Fabricantes
SLA6805M	High Voltage 3 phase Motor Driver IC.	Sanken
SDC1742	12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.	Analog Devices

DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.

DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar