|
|
Número de pieza | PM2-LL10 | |
Descripción | Convergent Reflective Micro Photoelectric Sensor | |
Fabricantes | Panasonic | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de PM2-LL10 (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
No Preview Available ! 453
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
LIGHT CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC ELECTRICITY
PREVENTION
DEVICES
LASER
MARKERS
PLC
HUMAN MACHINE
INTERFACES
ENERGY CONSUMPTION
VISUALIZATION
COMPONENTS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
Selection
Guide
U-shaped
Convergent
Reflective
PM2
Convergent Reflective Micro Photoelectric Sensor Amplifier Built-in
PM2 SERIES
■■General terms and conditions............ F-13
■■Related Information
Glossary of terms........................ P.1455~
■■Sensor selection guide.................. P.427~
■■General precautions.................... P.1458~
Conforming to
EMC Directive
Certified
panasonic.net/id/pidsx/global
Convergent reflection sensing ensures stable detection
Stable detection by convergent reflective mode
Stable detection
characteristics are
obtained since it is
convergent reflective
type and senses a
limited area.
Detects
an object
within the
convergent
area
Hardly affected by background
Even a specular
background does not
affect the sensing
performance if the
sensor is located 30 mm
1.181 in away from it.
30 mm
1.181 in
However, the specular background should be a
plane surface, directly facing the sensor. A spherical
or curved background may be detected.
Dark object detectable
Since the sensor is very
sensitive, it can detect
even a dark object of low
reflectivity.
Sensing object
Background
Cable type is also available
Cumbersome soldering is not required.
It saves space and improves reliability.
With connector
PM-2LH10
50 mm 1.969 in approx.
PM-2LH10
Optimum setting
distance is 5 mm 0.197 in
approx.
Minute object detectable
A ø0.05 mm ø0.002 in
copper wire can be
detected at a distance of
5 mm 0.197 in under the
optimum condition.
5 mm 0.197 in
approx.
ø0.05 mm ø0.002 in
copper wire
25 mm 0.984 in
approx.
Cable type
1 page 457
PM2Convergent Reflective Micro Photoelectric Sensor
SERIES
FIBER
SENSORS
PRECAUTIONS FOR PROPER USE
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
ELECTRICITY
PREVENTION
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
CONSUMPTION
VISUALIZATION
COMPONENTS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Connector type
Cautions in plugging or unplugging a connector
• Do not plug or unplug a connector more than
10 times.
• Be sure not to give stress more than 5 N to a
terminal of both a connector and a sensor.
If you do not follow the above cautions, it will
cause a poor contact.
Procedures of plugging or unplugging a connector
1 Insert a connector straight into a
sensor until the connector lug is
locked by the sensor hook.
Hook
Lug
2 W hen unplugging, give as much
stress as a connector lug can
be relieved from a hook. Then
unplug it.
5 N or less
Caution: B e sure to hold a
connector when plugging
or unplugging it. Do
not hold a terminal or
a cable when plugging
or unplugging the
connector. Otherwise, it
will cause a poor contact.
DIMENSIONS (Unit: mm in)
PM2-LH10 PM2-LH10B
Sensor
Selection
Guide
U-shaped
Convergent
Reflective
PM2
10
0.394
26
1.024
20
0.787
14
0.551
3.3
0.130
5
0.197
Sensing surface
Operation
indicator (Red)
8.4
0.331
4
0.157
15 7.2
0.591 0.283
2-mounting oblong holes
01.559101.6769 25
0.984
1 0.039
6
0.236
3.2
0.126
3.2
0.126
Refer to p.1458~ for general precautions.
Soldering (Both connector CN-13 and sensor)
• If soldering is done directly on the terminals, strictly
adhere to the conditions given below.
Soldering temperature
Soldering time
Soldering position
260 °C 500 °F or less
10 sec. or less
Refer to the below figure
Sensor
0V OUT+V
Connector
CN 13
0V OUT +V
1.5 mm
0.059 in
Soldering
position
Wiring
• The cable length must
be 2 m 6.562 ft, or
less, with 0.3 mm2,
or more, cable. If the
cable is extended for
more than 2 m 6.562 ft,
connect a capacitor of
10 µF approx. between
+V and 0 V terminals.
Cable
10 µF +
–
5 to 24 V DC
±10 %
The CAD data in the dimensions can be downloaded from our website.
PM2-LF10 PM2-LF10B
Sensor
26
1.024
20
0.787
14
3.30.551
0.130 10
0.394
5
0.197
15 7.2
0.591 0.283
Sensing surface
Operation
indicator (Red)
4 0.157
15
0.591 13
0.512
25
0.984
2-mounting oblong holes
1 0.039
6
0.236
3.2
0.126
8.4
0.331
4
0.157
3.2
0.126
5 Page |
Páginas | Total 6 Páginas | |
PDF Descargar | [ Datasheet PM2-LL10.PDF ] |
Número de pieza | Descripción | Fabricantes |
PM2-LL10 | Convergent Reflective Micro Photoelectric Sensor | Panasonic |
PM2-LL10-C1 | Convergent Reflective Micro Photoelectric Sensor | Panasonic |
PM2-LL10B | Convergent Reflective Micro Photoelectric Sensor | Panasonic |
PM2-LL10B-C1 | Convergent Reflective Micro Photoelectric Sensor | Panasonic |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |