|
|
PDF RWP06040-10 Data sheet ( Hoja de datos )
| Número de pieza | RWP06040-10 | |
| Descripción | Wideband Power Amplifier | |
| Fabricantes | RFHIC | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de RWP06040-10 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
Wideband Power Amplifier RWP06040-10
Product Features
• GaN on SiC Broadband High Power Amplifier
• 450 ~ 880MHz Operation Bandwidth
• Small Signal Gain 38dB min.
• 40W Typical. @ P3dB
Applications
• General Purpose
Package Type : DP-75
Description
The power amplifier module is designed for Broadcasting, Telecommunication, Medical and Other markets.
Operating frequency range is from 450 ~ 880MHz.
Gallium Nitride on SiC technology is used and attached on an aluminum sub carrier. Full in/out matching for broadband
performance is already applied.
Improved thermal handling by patented technology.
Electrical Specifications @ VCC = 28V; Tc = 45°C; ZS = ZL = 50Ω
PARAMETER
Operating Frequency
Small Signal Gain
Gain Variation vs Frequency
P3 dB
OIP3 @ Po = +33dBm
(1MHz Tone spacing, CW 2-Tone)
UNIT
MHz
dB
dBpp
dBm
dBm
MIN
450
38
-
44
49
TYP
-
40
±1
45
51
Input Return Loss
ACLR@Pout=28dBm
W-CDMA,64PCH,4FA
Spectrum Analyzer Setting :
RBW=30KHz, VBW=10KHz
Supply Voltage
Quiescent Current consumption
dB -
45
48
dBc
44
47
V 27.5
A-
-12
48
51
45
48
28
2.5
MAX
880
42
±2
-
-
-10
-
-
-
-
30
2.7
On/Off Switching Time*
uS -
3.0 5.0
Shut Down or Switch On/Off
0 - 0.5
TTL Voltage**
V
2.5 5 5.5
Note.
*. Gate On/Off : High speed switching
**. Drain On/Off : 500ms delay
CONDITION
-
-
-
450 ~ 880MHz
450 ~ 880 MHz
450MHz
-
△=5MHz
△=10MHz
880MHz
△=5MHz
△=10MHz
Vcc(=Vds)
-
On : TTL "Low"
Off : TTL "High"(30mA@Disable)
On : TTL “Low”(Enable)
Off : TTL “High”
Korean Facilities : 82-31-8069-3036 / [email protected]
US Facility : 919-677-8780 / [email protected]
1/8
All specifications may change without notice
Version 2.1
1 page  
Wideband Power Amplifier RWP06040-10
Precautions
1. This product is designed to be used for broadband
amplification. Heat generation is higher when there is no RF
signal in the device. Therefore, the worst case scenario is
when there is no RF signal, and the amplifier is “on” with
current draw.
The temperature must be calculated properly.
Case temperature must maintain below 80°C.
Right side drawing notes how to use a temperature
monitoring function to protect against overheating.
2. Thermal Grease or Metal Thermal Interface Materials are
recommended for heat dissipation. An example would be
spreading
thermal grease on the bottom of the device
RF IN
Vcc(+28V)
Shut Down
(+5V)
RF OUT
Temp Monitor
Switch ON/OFF
+Vcc
+
-
Ref Voltage
Korean Facilities : 82-31-8069-3036 / [email protected]
US Facility : 919-677-8780 / [email protected]
Comparator Block (with hysteresis gap)
All specifications may change without notice
5 / 8 Version 2.1
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet RWP06040-10.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| RWP06040-10 | Wideband Power Amplifier | RFHIC |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |