Datenblatt-pdf.com


LNK302P Schematic ( PDF Datasheet ) - Power Integrations

Teilenummer LNK302P
Beschreibung Energy-Efficient Off-Line Switcher IC
Hersteller Power Integrations
Logo Power Integrations Logo 




Gesamt 18 Seiten
LNK302P Datasheet, Funktion
LNK302/304-306
LinkSwitch-TN Family
Lowest Component Count, Energy-Efficient
Off-Line Switcher IC
Product Highlights
Cost Effective Linear/Cap Dropper Replacement
Lowest cost and component count buck converter solution
Fully integrated auto-restart for short-circuit and open loop
fault protection – saves external component costs
LNK302 uses a simplified controller without auto-restart for
very low system cost
66 kHz operation with accurate current limit – allows low cost
off-the-shelf 1 mH inductor for up to 120 mA output current
Tight tolerances and negligible temperature variation
High breakdown voltage of 700 V provides excellent input
surge withstand
Frequency jittering dramatically reduces EMI (~10 dB)
Minimizes EMI filter cost
High thermal shutdown temperature (+135 °C minimum)
Much Higher Performance Over Discrete Buck and
Passive Solutions
Supports buck, buck-boost and flyback topologies
System level thermal overload, output short-circuit and open
control loop protection
Excellent line and load regulation even with typical configuration
High bandwidth provides fast turn-on with no overshoot
Current limit operation rejects line ripple
Universal input voltage range (85 VAC to 265 VAC)
Built-in current limit and hysteretic thermal protection
Higher efficiency than passive solutions
Higher power factor than capacitor-fed solutions
Entirely manufacturable in SMD
EcoSmart– Extremely Energy Efficient
Consumes typically only 50/80 mW in self-powered buck
topology at 115/230 VAC input with no-load (opto feedback)
Consumes typically only 7/12 mW in flyback topology with
external bias at 115/230 VAC input with no-load
Meets California Energy Commission (CEC), Energy Star, and
EU requirements
Applications
Appliances and timers
LED drivers and industrial controls
Description
LinkSwitch-TN is specifically designed to replace all linear and
capacitor-fed (cap dropper) non-isolated power supplies in the
under 360 mA output current range at equal system cost while
offering much higher performance and energy efficiency.
LinkSwitch-TN devices integrate a 700 V power MOSFET,
oscillator, simple On/Off control scheme, a high-voltage switched
current source, frequency jittering, cycle-by-cycle current limit
FB BP
Wide+Range
High-Voltage
DS
LinkSwitch-TN
DC Input
+
DC
Output
Figure 1.
PI-3492-041509
Typical Buck Converter Application (See Application Examples Section
for Other Circuit Configurations).
Output Current Table1
Product4
LNK302P/G/D
LNK304P/G/D
LNK305P/G/D
LNK306P/G/D
230 VAC ±15%
MDCM2
CCM3
63 mA
80 mA
120 mA 170 mA
175 mA 280 mA
225 mA 360 mA
85-265 VAC
MDCM2
CCM3
63 mA
80 mA
120 mA 170 mA
175 mA 280 mA
225 mA 360 mA
Table 1. Output Current Table.
Notes:
1. Typical output current in a non-isolated buck converter. Output power capability
depends on respective output voltage. See Key Applications Considerations
Section for complete description of assumptions, including fully discontinuous
conduction mode (DCM) operation.
2. Mostly discontinuous conduction mode.
3. Continuous conduction mode.
4. Packages: P: DIP-8B, G: SMD-8B, D: SO-8C.
and thermal shutdown circuitry onto a monolithic IC. The start-up
and operating power are derived directly from the voltage on the
DRAIN pin, eliminating the need for a bias supply and associated
circuitry in buck or flyback converters. The fully integrated
auto-restart circuit in the LNK304-306 safely limits output power
during fault conditions such as short-circuit or open loop,
reducing component count and system-level load protection
cost. A local supply provided by the IC allows use of a non-
safety graded optocoupler acting as a level shifter to further
enhance line and load regulation performance in buck and
buck-boost converters, if required.
www.powerint.com
This Product is Covered by Patents and/or Pending Patent Applications.
June 2013






LNK302P Datasheet, Funktion
LNK302/304-306
Topology
High-Side
Buck –
Direct
Feedback
High-Side
Buck –
Optocoupler
Feedback
Low-Side
Buck –
Optocoupler
Feedback
Basic Circuit Schematic
FB BP
+D
S
VIN LinkSwitch-TN
Key Features
1. Output referenced to input
2.
3.
4.
PSLootewspitcidvoeoswot undtip–reuVcttO(Vf<eOe)VdwINbiathckre(s±p1e0c%t totyp-V.)IN
5. Requires an output load to maintain regulation
+
VO
FB BP
+D
S
LinkSwitch-TN
VIN
PI-3751-041509
+
VO
1. Output referenced to input
2. Positive output (VO) with respect to -VIN
3. Step down – VO < VIN
4. Optocoupler feedback
- Accuracy only limited by reference choice
- Low cost non-safety rated optocoupler
- No pre-load required
5. Minimum no-load consumption
PI-3752-041509
++
VIN LinkSwitch-TN
VO
Low-Side
Buck –
Constant
Current LED
Driver
High-Side
Buck-Boost –
Direct
Feedback
High-Side
Buck-Boost –
Constant
Current LED
Driver
BP FB
SD
+
LinkSwitch-TN
VIN
BP FB
SD
PI-3753-041509
IO
VF +
1. Output referenced to input
2.
3.
4.
ONStepegtpoacdtiovouewponleu–rtpfVeuOet d<(VbVOa)IcNwkith
respect
to
+VIN
- Accuracy only limited by reference choice
- Low cost non-safety rated optocoupler
- No pre-load required
- Ideal for driving LEDs
R
=
VF
IO
PI-3754-041509
FB BP
+D
S
VIN LinkSwitch-TN
VO
FB BP
+D
S
VIN LinkSwitch-TN
300
2 k
RSENSE
PI-3755-041509
RSENSE =
2V
IO
IO
10 µF 100 nF
50 V
1. Output referenced to input
2.
3.
4.
NLSoteewgpacutiovpse/tdodouiwrtepncut–t f(eVVeOOd)>bwaVitcINhkor(er±Vs1pO0e<%ctVttIyNop+.)VIN
5. Fail-safe – output is not subjected to input
voltage if the internal power MOSFET fails
6. Ideal for driving LEDs – better accuracy and
temperature stability than Low-side Buck
constant current LED driver
7. Requires an output load to maintain regulation
PI-3779-041509
Table 2. Common Circuit Configurations Using LinkSwitch-TN. (continued on next page)
6
Rev. J 06/13
www.powerint.com

6 Page









LNK302P pdf, datenblatt
LNK302/304-306
S1
50 V
470 Ω
5W
D FB
BP
SS
SS
470 kΩ
0.1 μF
S2
50 V
Figure 7. LinkSwitch-TN General Test Circuit.
Figure 8. LinkSwitch-TN Duty Cycle Measurement.
DCMAX
(internal signal)
FB
tP
VDRAIN
tP
=
1
fOSC
tEN
Figure 9. LinkSwitch-TN Output Enable Timing.
PI-3490-060204
PI-3707-112503
12
Rev. J 06/13
www.powerint.com

12 Page





SeitenGesamt 18 Seiten
PDF Download[ LNK302P Schematic.PDF ]

Link teilen




Besondere Datenblatt

TeilenummerBeschreibungHersteller
LNK302DEnergy-Efficient Off-Line Switcher ICPower Integrations
Power Integrations
LNK302GEnergy-Efficient Off-Line Switcher ICPower Integrations
Power Integrations
LNK302PEnergy-Efficient Off-Line Switcher ICPower Integrations
Power Integrations

TeilenummerBeschreibungHersteller
CD40175BC

Hex D-Type Flip-Flop / Quad D-Type Flip-Flop.

Fairchild Semiconductor
Fairchild Semiconductor
KTD1146

EPITAXIAL PLANAR NPN TRANSISTOR.

KEC
KEC


www.Datenblatt-PDF.com       |      2020       |      Kontakt     |      Suche