|
|
Número de pieza | SS2406 | |
Descripción | Hall Latch - High Sensitivity | |
Fabricantes | SEC | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de SS2406 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
No Preview Available ! Packages
3 pin SOT23 (suffix SO)
SS2406
Hall Latch - High Sensitivity
3 pin SIP (suffix UA)
Features and Benefits
– Wide operating voltage range from 2.5V to
24V
– High magnetic sensitivity – Multi-purpose
– DMOS technology
– Low current consumption
– Chopper-stabilized amplifier stage
– Open drain output
– Superior temperature stability
– Insensitive to physical stress
– SOT23 3L and flat SIP 3L
both RoHS Compliant packages
Functional Block Diagram
VDD
Voltage
Regulator
Chopper
Application Examples
– Automotive, Consumer and Industrial
– Solid-state switch
– Brushless DC motor commutation
– Speed detection
OUT – Angular position detection
– Linear position detection
– Proximity detection
Hall
Plate
GND
SIP Package
Pin 1 – VDD
Pin 2 – GND
Pin 3 – OUT
SOT Package
Pin 1 – VDD
Pin 2 – OUT
Pin 3 – GND
General Description
The SS2406 is a Hall-effect sensor IC fabricated from
mixed signal DMOS technology. The device inte-
grates a voltage regulator, Hall sensor with dynamic
offset cancellation system, Schmitt trigger and an
open-drain output driver, all in a single package.
It incorporates advanced chopper stabilization techniques to provide accurate and stable magnetic switch points.
There are many applications for this HED - Hall Electronic Device - in addition to those listed above. The design,
specifications and performance have been optimized for commutation applications in 5V and 12V brushless DC
motors.
Thanks to its wide operating voltage range and extended choice of temperature range, it is quite suitable for use in
automotive, industrial and consumer applications.
The device is delivered in a Small Outline Transistor (SOT) for surface mount process or in a Plastic Single In
Line (TO92) for through- hole mount. Both 3-lead packages are RoHS compliant.
1 V3.10 Nov 1, 2013
1 page SS2406
Hall Latch - High Sensitivity
netic fields with equivalent strength and opposite direction drive the output high and low.
Powering-on the device in the hysteresis region (less than BOP and higher than BRP) allows an indeterminate output
state. The correct state is attained after the first excursion beyond BOP or BRP.
The SOT-23 device is reversed from the UA package. The SOT-23 output transistor will be latched on in the pres-
ence of a sufficiently strong North pole magnetic field applied to the marked face.
Application Information
It is strongly recommended that an external bypass capacitor be connected (in close proximity to the Hall sensor) be-
tween the supply (VDD Pin) and ground (GND Pin) of the device to reduce both external noise and noise generated by
the chopper stabilization technique. As is shown in the following two figures in next page, a 0.1μF capacitor is typical.
Typical Three-Wire Application Circuit
C1 VDD
R2
OUT
SS2406
GND
C2
For reverse voltage protection, it is recommended to connect a resistor or a diode in series with the VDD pin. When
using a resistor, three points are important:
- the resistor has to limit the reverse current to 50mA maximum (VCC / R1 ≤ 50mA)
- the resulting device supply voltage VDD has to be higher than VDD min (VDD = VCC – R1*IDD)
- the resistor has to withstand the power dissipated in reverse voltage condition (PD = VCC2/R1)
When using a diode, a reverse current cannot flow and the voltage drop is almost constant (≈0.7V).
Therefore, a 100Ω/0.25W resistor for 5V application and a diode for higher supply voltage are recommended. Both
solutions provide the required reverse voltage protection.
When a weak power supply is used or when the device is intended to be used in noisy environment, it is recommended
the following figure is used.
The low-pass filter formed by R1 and C1 and the Zener diode Z1 bypass the disturbances or voltage spikes occurring
on the device supply voltage VDD. The diode D1 provides additional reverse voltage protection.
Automotive and Severe Environment Protection Circuit
R1:100
D1
Z1
C1
VDD
SS2406
OUT
GND
R2
C2
5 V3.10 Nov 1, 2013
5 Page |
Páginas | Total 8 Páginas | |
PDF Descargar | [ Datasheet SS2406.PDF ] |
Número de pieza | Descripción | Fabricantes |
SS240 | 2.0 AMP SURFACE MOUNT SCHOTTKY BARRIER RECTIFIERS | GW |
SS2406 | Hall Latch - High Sensitivity | SEC |
SS240F | Schottky Diodes | Kexin |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |