|
|
Número de pieza | BD00HC5WEFJ | |
Descripción | 1.5A Secondary Variable Output LDO Regulators | |
Fabricantes | ROHM Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de BD00HC5WEFJ (archivo pdf) en la parte inferior de esta página. Total 12 Páginas | ||
No Preview Available ! Secondary Variable Output LDO Regulator Series for Local Power Supplies
1.5A Secondary Variable Output
LDO Regulators for Local Power Supplies
BD00HC5WEFJ
No.10026EAT09
●Description
BD00HC5WEFJ is a LDO regulator with output current 1.5A. The output accuracy is ±1% of output voltage. With
external resistance, it is available to set the output voltage at random (from 1.5V to 7.0V) and also provides output
voltage fixed type without external resistance. It is used for the wide applications of digital appliances. It has package
type: HTSOP-J8. Over current protection (for protecting the IC destruction by output short circuit), circuit current
ON/OFF switch (for setting the circuit 0μA at shutdown mode), and thermal shutdown circuit (for protecting IC from heat
destruction by over load condition) are all built in. It is usable for ceramic capacitor and enables to improve smaller set
and long-life.
●Features
1) Output current 1.5A
2) High accuracy reference voltage circuit
3) Built-in Over Current Protection circuit (OCP)
4) Built-in Thermal Shut Down circuit (TSD)
5) With shut down switch
6) Output voltage variable type (1.5V to 7.0V)
7) Package: HTSOP-J8
●Output voltage differential Line up
Product name
BD00HC5WEFJ
Variable Package
○ HTSOP-J8
Product name : BD00HC5WEFJ
abc d e
Signal
a
b
c
d
e
Description
Output voltage (V)
00 Variable
Voltage resistance(V)
E 24V H 10V
F 20V
I
7V
G 15V
Output current (A)
A1 0.1A C0 1.0A
A3 0.3A C5 1.5A
A5 0.5A D0 2.0A
Shutdown switch
“W” Shutdown switch is built in
“ ” Shutdown switch is not built in
Package
EFJ HTSOP-J8
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
1/11
2010.04 - Rev.A
1 page BD00HC5WEFJ
Technical Note
●Heat Dissipation Characteristics
◎HTSOP-J8
Measure condition: mounted on a ROHM board, and IC
4.0 ⑤3.76W
3.0
Substrate size: 70mm × 70mm × 1.6mm
(Substrate with thermal via)
・Solder the substrate and package reverse exposure heat
radiation part
④2.11W
2.0
① IC only
θj-a=249.5℃/W
③1.10W
1.0 ②0.82W
①0.50W
② 1-layer(copper foil are :0mm×0mm)
θj-a=153.2℃/W
③ 2-layer(copper foil are :15mm×15mm)
0 θj-a=113.6℃/W
0
25 50 75 100
125 150 ④ 2-layer(copper foil are :70mm×70mm)
Ambien周t 囲Te温mp度e:rTaatu[r℃e ]:Ta [℃]
θj-a=59.2℃/W
⑤ 4-layer(copper foil are :70mm×70mm)
θj-a=33.3℃/W
●About Input-to-output capacitor
It is recommended that a capacitor is placed nearby pin between Input pin and GND, output pin and GND.
A capacitor, between input pin and GND, is valid when the power supply impedance is high or drawing is long. Also as for a
capacitor, between output pin and GND, the greater the capacity, more sustainable the line regulation and it makes improvement
of characteristics by load change. However, please check by mounted on a board for the actual application. Ceramic capacitor
usually has difference, thermal characteristics and series bias characteristics, and moreover capacity decreases gradually by
using conditions.
For more detail, please be sure to inquire the manufacturer, and select the best ceramic capacitor.
Ceramic capacitor capacity- DC bias characteristics
(Characteristics example)
10
0
-10
-20
-30
-40
-50
-60
-70
10 Voltage Resistance
F characteristics
10 Voltage resistance
B1 characteristics
GRM188B11A105KA61D
10 Voltage resistance
B characteristics
6.3 Voltage resistance
B characteristics
10 Voltage resistance
F characteristics
4 Voltage resistance
X6S characteristics
-80
-90
-100
0
123
DC Bias Voltage [V]
4
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
5/11
2010.04 - Rev.A
5 Page BD00HC5WEFJ
●Type Designations (Ordering Information)
BD 0 0 H
C5
W
Technical Note
EFJ -E2
ROHM
Part Number
Output voltage
00 : Variable
Voltage
resistance
E:24V
F:20V
G:15V
H:10V
I:7V
Output cuurent
A1:0.1A
A3:0.3A
A5:0.5A
C0:1.0A
C5:1.5A
D0:2.0A
Shutdown switch
“W”:Built in
“ ”:None
Package
EFJ :HTSOP-J8
Packaging
specifications
E2:Emboss tape reel
HTSOP-J8
4.9±0.1
(MAX 5.25 include BURR)
(3.2)
8765
4°
+6°
−4°
0.545
1 234
1PIN MARK
S
+0.05
0.17 -0.03
1.27
+0.05
0.42 -0.04 0.08 M
0.08 S
(Unit : mm)
<Tape and Reel information>
Tape
Quantity
Embossed carrier tape
2500pcs
Direction
of feed
E2
( )The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
Reel
1pin Direction of feed
∗Order quantity needs to be multiple of the minimum quantity.
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
11/11
2010.04 - Rev.A
11 Page |
Páginas | Total 12 Páginas | |
PDF Descargar | [ Datasheet BD00HC5WEFJ.PDF ] |
Número de pieza | Descripción | Fabricantes |
BD00HC5WEFJ | 1.5A Secondary Variable Output LDO Regulators | ROHM Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |